WatchGas SST Reducer Set SST4-7SOL-Reducer-Set
Description
The
WatchGas SST Reducer Set (SST4-7SOL-Reducer-Set) bridges 3×5 mm and 5×8 mm sampling tubing lines in WatchGas gas detection setups. Use it when a sampling configuration mixes tubing diameters — for example, connecting a short 5×8 mm section at the detector inlet to a longer 3×5 mm run to the sampling probe. Pressure is maintained across the transition; there is no flow disruption or leak point when fittings are correctly seated.
Compatible with the
SST4-PUMP sample-draw system and any SST1 monitor using probe-based sampling configurations. Used alongside
Last-O-More Tubing (3×5 mm) and the
SST4-PUMP-ACC sampling kit to complete extended sampling line builds.
Specifications: Bridges 3×5 mm and 5×8 mm tubing | Designed for WatchGas SST sampling lines | Low-profile fitting, no tools required for installation.
Technical documents:
SST Accessories Brochure
Brochure
Frequently Asked Questions
What tubing sizes does the SST Reducer Set connect?
The SST Reducer Set connects 3×5 mm tubing (inner diameter 3 mm, outer diameter 5 mm) to 5×8 mm tubing (inner diameter 5 mm, outer diameter 8 mm). This is the most common tubing-diameter transition in WatchGas SST sampling configurations — 3×5 mm is used for long sampling runs; 5×8 mm appears at monitor inlets and demand flow regulators.
Which WatchGas products use this reducer set?
The reducer set is most commonly used with the
SST4-PUMP in sample-draw configurations and with SST1 monitors in probe-sampling setups. It pairs with
Last-O-More Tubing and the
demand flow regulator.
Is the reducer set reusable?
Yes. The SST Reducer Set fittings are designed for repeated assembly and disassembly. They can be removed, repositioned, and reinstalled when reconfiguring sampling line lengths or swapping between monitoring setups. Inspect fittings for wear or cracking periodically — replace if seating is not tight.
Read more
Description
The WatchGas SST Reducer Set (SST4-7SOL-Reducer-Set) bridges 3×5 mm and 5×8 mm sampling tubing lines in WatchGas gas detection setups. Use it when a sampling configuration mixes tubing diameters — for example, connecting a short 5×8 mm section at the detector inlet to a longer 3×5 mm run to the sampling probe. Pressure is maintained across the transition; there is no flow disruption or leak point when fittings are correctly seated.
Compatible with the SST4-PUMP sample-draw system and any SST1 monitor using probe-based sampling configurations. Used alongside Last-O-More Tubing (3×5 mm) and the SST4-PUMP-ACC sampling kit to complete extended sampling line builds.
Specifications: Bridges 3×5 mm and 5×8 mm tubing | Designed for WatchGas SST sampling lines | Low-profile fitting, no tools required for installation.
Technical documents:
SST Accessories Brochure
Brochure
Frequently Asked Questions
What tubing sizes does the SST Reducer Set connect?
The SST Reducer Set connects 3×5 mm tubing (inner diameter 3 mm, outer diameter 5 mm) to 5×8 mm tubing (inner diameter 5 mm, outer diameter 8 mm). This is the most common tubing-diameter transition in WatchGas SST sampling configurations — 3×5 mm is used for long sampling runs; 5×8 mm appears at monitor inlets and demand flow regulators.
Which WatchGas products use this reducer set?
The reducer set is most commonly used with the SST4-PUMP in sample-draw configurations and with SST1 monitors in probe-sampling setups. It pairs with Last-O-More Tubing and the demand flow regulator.
Is the reducer set reusable?
Yes. The SST Reducer Set fittings are designed for repeated assembly and disassembly. They can be removed, repositioned, and reinstalled when reconfiguring sampling line lengths or swapping between monitoring setups. Inspect fittings for wear or cracking periodically — replace if seating is not tight.
The WatchGas SST Reducer Set (SST4-7SOL-Reducer-Set) bridges 3×5 mm and 5×8 mm sampling tubing lines in WatchGas gas detection setups. Use it when a sampling configuration mixes tubing diameters — for example, connecting a short 5×8 mm section at the detector inlet to a longer 3×5 mm run to the sampling probe. Pressure is maintained across the transition; there is no flow disruption or leak point when fittings are correctly seated.
Compatible with the SST4-PUMP sample-draw system and any SST1 monitor using probe-based sampling configurations. Used alongside Last-O-More Tubing (3×5 mm) and the SST4-PUMP-ACC sampling kit to complete extended sampling line builds.
Specifications: Bridges 3×5 mm and 5×8 mm tubing | Designed for WatchGas SST sampling lines | Low-profile fitting, no tools required for installation.
Technical documents:
SST Accessories Brochure
Brochure
Frequently Asked Questions
What tubing sizes does the SST Reducer Set connect?
The SST Reducer Set connects 3×5 mm tubing (inner diameter 3 mm, outer diameter 5 mm) to 5×8 mm tubing (inner diameter 5 mm, outer diameter 8 mm). This is the most common tubing-diameter transition in WatchGas SST sampling configurations — 3×5 mm is used for long sampling runs; 5×8 mm appears at monitor inlets and demand flow regulators.
Which WatchGas products use this reducer set?
The reducer set is most commonly used with the SST4-PUMP in sample-draw configurations and with SST1 monitors in probe-sampling setups. It pairs with Last-O-More Tubing and the demand flow regulator.
Is the reducer set reusable?
Yes. The SST Reducer Set fittings are designed for repeated assembly and disassembly. They can be removed, repositioned, and reinstalled when reconfiguring sampling line lengths or swapping between monitoring setups. Inspect fittings for wear or cracking periodically — replace if seating is not tight.
Specifications
Specifications
-
MPN
-
Product Weight (lbs.)
-
Country of Origin
Reviews
Reviews
Keep your team protected & compliant!
- Expert guidance tailored to your specific needs
- Access responsive customer support when you need it
- Enjoy fast shipping directly to your location
- Benefit from extensive industry knowledge—75+ years of experience
- In-house gas detection calibration & repair services available
