RAE Systems Constant Flow Regulator, .5 LPM / 34 Liter
Description
This constant flow regulator is a calibration accessory for RAE Systems monitors. 002-3011-000 delivers a 0.5 liter-per-minute flow from a 34-liter steel calibration cylinder, which is the standard draw rate for diffusion monitors that do not run their own pump during a bump test or calibration.
Fit and Specifications
- Constant flow regulator, 0.5 LPM, part number 002-3011-000
- Fits 34-liter steel calibration gas cylinders
- Right flow for diffusion monitors during bump test and calibration
- Threaded C-10 connection; threads directly onto the cylinder
Compatibility and Ordering
Match the part number (002-3011-000) to the part you are replacing, and confirm your monitor model before you order. Buyers of this 0.5 LPM regulator already own RAE Systems monitor, so the fastest check is the model label on the back of the unit. If the label is worn or the unit is an older or modified configuration, call us with the serial number and we will verify fit against the RAE Systems monitor before anything ships.
Bump test the monitor after any repair or consumable change, and calibrate per the manufacturer's instructions and your site procedure.
PK Safety is a Factory Authorized RAE Systems Service Center with in-house technicians, so this 0.5 LPM regulator ships from the shop that services your monitor. Questions on fit or quantity? Call 800.829.9580.
Part Number:
002-3011-000
Frequently Asked Questions
Why 0.5 LPM instead of 1 LPM?
Diffusion monitors do not pull air with a pump, so they are calibrated at a lower flow. Pushing 1 LPM into a diffusion sensor can over-pressurize the sample path. Use 0.5 LPM for diffusion units and 1 LPM for pumped units.
Which cylinders fit this regulator?
It is designed for 34-liter steel RAE Systems calibration gas cylinders. For 58-liter or 103-liter cylinders, see the 1 LPM regulator.
Is 002-3011-000 compatible with my monitor?
Yes for diffusion RAE Systems monitors. Call us with your model and we will confirm whether 0.5 LPM or 1 LPM is correct for your bump test and calibration setup.
Do I need to recalibrate anything after installing it?
Changing the regulator does not change calibration. Use the correct flow during the next calibration and follow the manufacturer's instructions and your site procedure.
Related Searches
Calibration Gas, RAE Systems, Gas Detection, Gas Detector Accessories
Read more
Description
This constant flow regulator is a calibration accessory for RAE Systems monitors. 002-3011-000 delivers a 0.5 liter-per-minute flow from a 34-liter steel calibration cylinder, which is the standard draw rate for diffusion monitors that do not run their own pump during a bump test or calibration.
Fit and Specifications
- Constant flow regulator, 0.5 LPM, part number 002-3011-000
- Fits 34-liter steel calibration gas cylinders
- Right flow for diffusion monitors during bump test and calibration
- Threaded C-10 connection; threads directly onto the cylinder
Compatibility and Ordering
Match the part number (002-3011-000) to the part you are replacing, and confirm your monitor model before you order. Buyers of this 0.5 LPM regulator already own RAE Systems monitor, so the fastest check is the model label on the back of the unit. If the label is worn or the unit is an older or modified configuration, call us with the serial number and we will verify fit against the RAE Systems monitor before anything ships.
Bump test the monitor after any repair or consumable change, and calibrate per the manufacturer's instructions and your site procedure.
PK Safety is a Factory Authorized RAE Systems Service Center with in-house technicians, so this 0.5 LPM regulator ships from the shop that services your monitor. Questions on fit or quantity? Call 800.829.9580.
Part Number:
002-3011-000
Frequently Asked Questions
Why 0.5 LPM instead of 1 LPM?
Diffusion monitors do not pull air with a pump, so they are calibrated at a lower flow. Pushing 1 LPM into a diffusion sensor can over-pressurize the sample path. Use 0.5 LPM for diffusion units and 1 LPM for pumped units.
Which cylinders fit this regulator?
It is designed for 34-liter steel RAE Systems calibration gas cylinders. For 58-liter or 103-liter cylinders, see the 1 LPM regulator.
Is 002-3011-000 compatible with my monitor?
Yes for diffusion RAE Systems monitors. Call us with your model and we will confirm whether 0.5 LPM or 1 LPM is correct for your bump test and calibration setup.
Do I need to recalibrate anything after installing it?
Changing the regulator does not change calibration. Use the correct flow during the next calibration and follow the manufacturer's instructions and your site procedure.
Related Searches
Calibration Gas, RAE Systems, Gas Detection, Gas Detector Accessories
This constant flow regulator is a calibration accessory for RAE Systems monitors. 002-3011-000 delivers a 0.5 liter-per-minute flow from a 34-liter steel calibration cylinder, which is the standard draw rate for diffusion monitors that do not run their own pump during a bump test or calibration.
Fit and Specifications
- Constant flow regulator, 0.5 LPM, part number 002-3011-000
- Fits 34-liter steel calibration gas cylinders
- Right flow for diffusion monitors during bump test and calibration
- Threaded C-10 connection; threads directly onto the cylinder
Compatibility and Ordering
Match the part number (002-3011-000) to the part you are replacing, and confirm your monitor model before you order. Buyers of this 0.5 LPM regulator already own RAE Systems monitor, so the fastest check is the model label on the back of the unit. If the label is worn or the unit is an older or modified configuration, call us with the serial number and we will verify fit against the RAE Systems monitor before anything ships.
Bump test the monitor after any repair or consumable change, and calibrate per the manufacturer's instructions and your site procedure.
PK Safety is a Factory Authorized RAE Systems Service Center with in-house technicians, so this 0.5 LPM regulator ships from the shop that services your monitor. Questions on fit or quantity? Call 800.829.9580.
Part Number:
002-3011-000
Frequently Asked Questions
Why 0.5 LPM instead of 1 LPM?
Diffusion monitors do not pull air with a pump, so they are calibrated at a lower flow. Pushing 1 LPM into a diffusion sensor can over-pressurize the sample path. Use 0.5 LPM for diffusion units and 1 LPM for pumped units.
Which cylinders fit this regulator?
It is designed for 34-liter steel RAE Systems calibration gas cylinders. For 58-liter or 103-liter cylinders, see the 1 LPM regulator.
Is 002-3011-000 compatible with my monitor?
Yes for diffusion RAE Systems monitors. Call us with your model and we will confirm whether 0.5 LPM or 1 LPM is correct for your bump test and calibration setup.
Do I need to recalibrate anything after installing it?
Changing the regulator does not change calibration. Use the correct flow during the next calibration and follow the manufacturer's instructions and your site procedure.
Related Searches
Calibration Gas, RAE Systems, Gas Detection, Gas Detector Accessories
Specifications
Specifications
-
Product Weight (lbs.)
-
Height (in.)
-
Length (in.)
-
Width (in.)
-
Country of Origin
Reviews
Reviews
Keep your team protected & compliant!
- Expert guidance tailored to your specific needs
- Access responsive customer support when you need it
- Enjoy fast shipping directly to your location
- Benefit from extensive industry knowledge—75+ years of experience
- In-house gas detection calibration & repair services available
